Italiano:
Sistema di ventilazione con filtro HEPA, tramite ventola PC 5V 12cm ACP12025 (120x120x25 mm DC5V) e filtro HEPA H12 lavabile 150 x 120 x 25 ASIN: B081T3M6KF (utilizzato da ELECTROLUX EL4100, EL6986A, EL4050, ZUA3840P, ZE346B, Z3347, ZU3375, US3940P, ZE360WP, ZSC69FD2, ZSC6940, ZUAG3801, ZUA3940P, ZUSG3901, ZSC6940, da Philips FC9080, FC9081, FC9082, FC9083, FC9084, FC9085, FC9086, FC9087, FC9088, FC9089, FC9008, FC9022, FC9023, FC9054, FC9057, FC9064, FC9104, FC9116, FC9122, FC9131, FC9171, FC9200, FC9204, FC9206, FC9208, FC9209, FC9066, FC9067, FC9222, FC9262, FC9264, FC9225, FC9266, FC9252, FC9254, FC9256, FC9258, FC9261, FC9302, FC9304).
Per il fissaggio sono state utilizzate viti per il legno 4x16 mm, le quali si avvitano sui fori della ventola tramite un adattatore "Spina_per_vite.stl", nel caso si utilizzino viti più larghe, non è necessario utilizzare l'adattatore.

English:
HEPA Filter Ventilation System, by PC 5V 12cm fan ACP12025 (120x120x25 mm DC5V) and washable HEPA H12 filter 150 x 120 x 25 ASIN: B081T3M6KF (used by ELECTROLUX EL4100, EL6986A, EL4050, ZUA3840P, ZE346B, Z3347, ZU3375, US3940P, ZE360WP, ZSC69FD2, ZSC6940, ZUAG3801, ZUA3940P, ZUSG3901, ZSC6940, by Philips FC9080, FC9081, FC9082, FC9083, FC9084, FC9085, FC9086, FC9087, FC9088, FC9089, FC9008, FC9022, FC9023, FC9054, FC9057, FC9064, FC9104, FC9116, FC9122, FC9131, FC9171, FC9200, FC9204, FC9206, FC9208, FC9209, FC9066, FC9067, FC9222, FC9262, FC9264, FC9225, FC9266, FC9252, FC9254, FC9256, FC9258, FC9261, FC9302, FC9304).
For fixing, 4x16 mm wood screws were used, which are screwed into the holes of the fan using an adapter "Spina_per_vite.stl". If you use wider screws, it is not necessary to use the adapter.

Istruction for box
https://www.instructables.com/Enclosure-for-3d-printer-using-Ikea-box/

Si consiglia l'abbinamento con:
Recommended pairing with:
https://www.thingiverse.com/thing:6984146
https://www.thingiverse.com/thing:6984150

Artillery Hornet Firmware (290°C & Input shaping):
https://github.com/fanXbox/hornet-firmware/releases

Artillery

Artillery Hornet

No

No

0,2

5

nozzle=0,4 mm

acceleration_print = 1500.0
acceleration_travel = 3000.0
bridge_fan_speed_3 = 100.0
bridge_skin_density_2 = 75.0
bridge_skin_density_3 = 100.0
bridge_skin_material_flow_3 = 100.0
bridge_skin_speed = 20.0
bridge_skin_speed_3 = 40.0
brim_width = 8.0
coasting_enable = True
connect_infill_polygons = True
cool_fan_enabled = True
cool_fan_full_at_height = 1
cool_fan_speed = 50
cool_lift_head = True
cool_min_temperature = 285.0
gradual_infill_step_height = 15.0
hole_xy_offset = 0.4
infill_line_distance = =0 if infill_sparse_density == 0 else (infill_line_width 100) / infill_sparse_density (2 if infill_pattern == 'grid' else (3 if infill_pattern == 'triangles' or infill_pattern == 'trihexagon' or infill_pattern == 'cubic' or infill_pattern == 'cubicsubdiv' else (2 if infill_pattern == 'tetrahedral' or infill_pattern == 'quarter_cubic' else (1 if infill_pattern == 'cross' or infill_pattern == 'cross_3d' else (1.6 if infill_pattern == 'lightning' else 1)))))
infill_multiplier = 2
infill_pattern = gyroid
infill_randomize_start_location = True
infill_sparse_density = 5
infill_sparse_thickness = 0.3
infill_wall_line_count = 1
inset_direction = inside_out
ironing_enabled = False
ironing_only_highest_layer = False
ironing_pattern = concentric
jerk_print = 20.0
material_alternate_walls = True
material_final_print_temperature = 280.0
material_initial_print_temperature = 280.0
material_print_temperature = 280
material_print_temperature_layer_0 = =material_print_temperature
minimum_support_area = 3
optimize_wall_printing_order = True
raft_base_speed = 40.0
raft_interface_speed = 40
raft_margin = 8.0
retract_at_layer_change = True
retraction_amount = 2.0
retraction_hop = 0.4
retraction_hop_enabled = True
retraction_hop_only_when_collides = True
retraction_speed = 40
scarf_joint_seam_length = 4
scarf_split_distance = 1
skin_edge_support_thickness = 0.5
skin_monotonic = True
skirt_brim_minimal_length = 200
skirt_line_count = 3
speed_infill = 100.0
speed_print = 100.0
speed_topbottom = 100
speed_travel = 200.0
speed_wall_x = 75.0
support_angle = 46
support_brim_width = 5.0
support_fan_enable = True
support_pattern = gyroid
support_tree_angle = 50.0
support_tree_min_height_to_model = 2
top_bottom_thickness = 1.5
wall_line_count = =1 if magic_spiralize else max(1, round((wall_thickness - wall_line_width_0) / wall_line_width_x) + 1) if wall_thickness != 0 else 0
wall_overhang_angle = 45
wall_overhang_speed_factor = 50.0
wall_thickness = 1.2
z_seam_corner = z_seam_corner_inner
z_seam_type = random
zig_zaggify_infill = True