This is designed to fit a Samsung wall charger along with a cable wrapped around it.
It's based on the USA/North American "Fast Charger" version of the charger but it might work with others.

It also has storage for two micro-sd cards in the top. It needs to be noted that the charger MUST be in to prevent the micro-sd cards from falling out. They fit somewhat loosely since my previous version was too tight and the card got stuck. I also put a pokey hole on the side to push out an SD card in the event it does get stuck (which it shouldn't unless it's sticky for some reason).

This is somewhat of a spin-off of the other Samsung charger cable wrap I made; I was inspired when the print failed while printing the other one (I was futzing with stuff while it was printing). The failed version worked somewhat but needed some adjustments.

I printed this and it works OK. It's not great but it works. I might make some changes eventually.

The benefit over my other version is this one takes much less time to print: Roughly an 1hr 45mins at .25mm layer height @ 40mm/sec.

PLA is what I used and it's strong..Very strong.

You MUST print with support "Everywhere". There will be some support material in the micro-sd holder but it's not too hard to get out with the right tools (small metal pick works).

Included is the file and also the general shape of the Samsung charger for anyone to use to make their own stuff.

I highly urge people to use the dimensions/template I included to make their own designs.
Note that the dimensions in the references are slightly larger (by roughly.05mm) to compensate for tolerances. Keep this in mind when you're designing your own whatever from this. Some things like the chamfers and fillets are mostly guessed based on the overall dimensions and look. Don't count on those being 100 percent accurate.

Be sure to check out this remix by Jimbo70 which removes the need for overhangs and supports AND allows for using two different color filaments.
https://www.thingiverse.com/thing:2958641

Print instructions

Category: Mobile Phone Summary

This is designed to fit a Samsung wall charger along with a cable wrapped around it.
It's based on the USA/North American "Fast Charger" version of the charger but it might work with others.

It also has storage for two micro-sd cards in the top. It needs to be noted that the charger MUST be in to prevent the micro-sd cards from falling out. They fit somewhat loosely since my previous version was too tight and the card got stuck. I also put a pokey hole on the side to push out an SD card in the event it does get stuck (which it shouldn't unless it's sticky for some reason).

This is somewhat of a spin-off of the other Samsung charger cable wrap I made; I was inspired when the print failed while printing the other one (I was futzing with stuff while it was printing). The failed version worked somewhat but needed some adjustments.

I printed this and it works OK. It's not great but it works. I might make some changes eventually.

The benefit over my other version is this one takes much less time to print: Roughly an 1hr 45mins at .25mm layer height @ 40mm/sec.

PLA is what I used and it's strong..Very strong.

You MUST print with support "Everywhere". There will be some support material in the micro-sd holder but it's not too hard to get out with the right tools (small metal pick works).

Included is the file and also the general shape of the Samsung charger for anyone to use to make their own stuff.

I highly urge people to use the dimensions/template I included to make their own designs.
Note that the dimensions in the references are slightly larger (by roughly.05mm) to compensate for tolerances. Keep this in mind when you're designing your own whatever from this. Some things like the chamfers and fillets are mostly guessed based on the overall dimensions and look. Don't count on those being 100 percent accurate.

Be sure to check out this remix by Jimbo70 which removes the need for overhangs and supports AND allows for using two different color filaments.
https://www.thingiverse.com/thing:2958641

Print Settings

Printer Brand:

Wanhao

Printer:

Doesn't Matter

Supports:

.25

Infill:

Notes:

I used 4 walls. This will give it a lot more strength.