Decoración de pared que representa la Xbox.
Además del logotipo, hay una máscara para el posicionamiento correcto de las partes del logotipo.

Firmware de Artillery Hornet (290°C y modelado de entrada):

Artillería.

Aviación de artillería Hornet.

No.

No.

0,2

100

boquilla = 0,4 mm

Aceleración_impresión = 1500.0
Aceleración de viaje = 3000.0
bridge_fan_speed_3 = 100.0
bridge_skin_density_2 = 75.0
bridge_skin_density_3 = 100.0
bridge_skin_material_flow_3 = 100.0
bridge_skin_speed = 20.0
bridge_skin_speed_3 = 40.0
brim_width = 8.0
coasting_enable = Verdadero
connect_infill_polygons = True
cool_fan_enabled = Verdadero
Cool_fan_full_at_height = 1
cool_fan_speed = 50
cool_lift_head = Verdadero
Temperatura mínima genial = 285.0
gradual_infill_step_height = 15.0
hole_xy_offset = 0.4
infill_line_distance = =0 si infill_sparse_density == 0 else (infill_line_width 100) / infill_sparse_density (2 si infill_pattern == 'grid' else (3 si infill_pattern == 'triangles' o infill_pattern == 'trihexagon' o infill_pattern == 'cubic' o infill_pattern == 'cubicsubdiv' else (2 si infill_pattern == 'tetrahedral' o infill_pattern == 'quarter_cubic' else (1 si
infill_multiplier = 2
infill_pattern = gyroid
infill_randomize_start_location = Verdadero
infill_sparse_density = 5
infill_sparse_thickness = 0.3
infill_wall_line_count = 1
Inset_direction = de adentro hacia afuera.
planchado_habilitado = Falso
planchar_solo_capa_superior = Falso
Patrón de planchado = concéntrico.
jerk_print = 20.0
material_paredes_alternativas = Verdadero
material_final_temperatura_de_impresión = 280.0
material_temperatura_de_impresión_inicial = 280.0
material_temperatura_de_impresión = 280
material_print_temperature_layer_0 = =material_print_temperature
área_de_soporte_mínima = 3
optimize_wall_printing_order = Verdadero
raft_base_speed = 40.0
raft_interface_speed = 40
raft_margin = 8.0
retract_at_layer_change = Verdadero
retracción_cantidad = 2.0
retracción_hop = 0.4
retraction_hop_enabled = Verdadero
retracción_salto_solo_cuando_colisiona = Verdadero
Velocidad de retracción = 40
scarf_joint_seam_length = 4
scarf_split_distance = 1
skin_edge_support_thickness = 0.5
skin_monotonic = True
skirt_brim_minimal_length = 200
skirt_line_count = 3
speed_infill = 100.0
speed_print = 100.0
speed_topbottom = 100
speed_travel = 200.0
speed_wall_x = 75.0
Ángulo de soporte = 46
support_brim_width = 5.0
support_fan_enable = Verdadero
Patrón de soporte = giroide.
support_tree_angle = 50.0
support_tree_min_height_to_model = 2
top_bottom_thickness = 1.5
wall_line_count = =1 si magic_spiralize, de lo contrario, máximo (1, redondear ((wall_thickness - wall_line_width_0) / wall_line_width_x) + 1) si wall_thickness no es 0, de lo contrario, 0
壁の張り出し角度 = 45
wall_overhang_speed_factor = 50.0
wall_thickness = 1.2
z_seam_corner = z_seam_corner_inner
z_seam_type = aleatorio
zig_zaggify_infill = Verdadero