My next project: Voron Switchwire: https://www.thingiverse.com/thing:4596054
or https://hackaday.io/project/174810-voron-switchwire

Voron 2.4 full kit

Voron 2.4 CoreXY 3D Printer Kit

Voron 2.4 - upgrade aluminum alloy frame printed parts kit CNC machined Build Log of my own Voron 2.4 - 3D Printer with CoreXY Kinematics.My Voron 2.4 - Change Log 05.03 2021 Afterburner Aluminum Extruder - Voron 2.4 V2.601 UpgradeFunssor Afterburner - Aluminum Extruder16 10 2020 Voron 2.4 V2.601 Upgrade - Chamber Bottom Heater System.Testing. Will by updated soon...220V 500W Insulated PTC Ceramic Air HeaterVoron 2.4 V2.601 Upgrade - Chamber Bottom PTC Air Heater SystemThis easy setup with two stock self regulated PTC heater connected to 220VAC increase chamber temperature ~+10C. It takes ~30 minutes to get 46C air temperature inside chamber when bed cheater is set to 100C, hotend heater is off and exhaust fan is on (I have enclosure build with 4mm glass with no extra isolation).03 10 2020 (Updated: 07 11 2020Voron 2.4 V2.601 A,B and E stepper motors water cooling system.Will by updated soon...Trianglelab Stepper motor liquld cooling motor water cooling upgrade kit for Nema17 motor ETC.13 09 2020 Voron 2.4 - Serial Number: V2.60113 09 2020 Voron 2.4 - Serial Request - Discord User: DarekNorway#4785Voron V2.60112 09 2020 Voron 2.4 - Finished. Additional Chamber heater and A,B,E stepper motors liquid cooling will be installed out of scope.Voron 2.4 - Spiral vase mode - Afterburner, Dragon hotend, ABSVoron 2.4 built by DarekNorway16 07 2020 Voron 2.4 - Deck panel mesh screen, DIN-3 35 Rails, Filtered Main Inlet and Rocker Switch.Deck panel mesh screenVoron 2.4 - DIN-3 35mm Rails. II have used 330mm long rails from local store then designed bracket to keep 7.5mm vertical gap from the bottom deck panel. STL for it you can find here https://www.thingiverse.com/thing:4543792 Voron 2.4 - Filtered Main Inlet and Rocker Switch.12 07 2020 Corexy Belts - Voron 2.4Core XY kinematics works already.Corexy Belts - Voron 2.4 (A and B drive unit)Corexy Belts - Voron 2.4 (XY Joint)Parts:4m Neoprene Rubber With Fiberglass Core LL-2GT-6 RF GT2 (6mm width) Open Timing Belt.11 07 2020 X-Carriage assembly - Voron 2.4X-Carriage - Voron 2.4X-Carriage assembly parts- Voron 2.410 07 2020 Voron 2.4 (Direct Extruder). X-axis linear railsVoron 2.4 (Direct Extruder). X-axis linear railsVoron 2.4). X-axis linear rails - Installation. Parts:2x3D Printed rail center guide2xMGN9 L300 linear rails from Robotdigg30xSpring T-nut M330x M3x8mm Socket Head Cap Screw (BHCS). Tools:Digital Caliper, 2.5mm Hex Allen key09 07 2020 Voron 2.4 - Z Belt CoverVoron 2.4 - Z Belt CoverVoron 2.4 - Z Belt Cover - BeforeParts:4x 3D Printed Cover4x Hammer T-nut M34x M3x6 Button Head Cap Screw (BHCS)Tools:2mm Allen Hex Key27 06 2020 Z-axis Belting. Voron 2.4Voron 2.4 with Z-axis LL-2GT RF Belts (9mm width)Voron 2.4 - one of four GT2 Belts (910mm in length each)Parts:4m Neoprene Rubber With Fiberglass Core LL-2GT-9 RF GT2 (9mm width) Open Belt.Tools:Cutter Knife26 06 2020 Voron 2.4 - Z-DriveVoron 2.4 - 1 of 4 Z-Drive with Stepper MotorVoron 2.4 - Z-Drive - PartsVoron 2.4 - Z-Drive - Upside DownMore photos of my Voron 2.4 3D printer you can find in the slideshow box above.Parts:(Soon)Tools:(Soon)22 06 2020 Back and Deck panels for Voron 2.4 Voron 2.4 Back Panel made from 4mm thick glass.Voron 2.4 - Deck Panel made from 4mm thick glass. Fastened to the two heated bed support profiles by heavy duty mounting tape.Parts:(Soon)Tools:(Soon)17 06 2020 Voron 2.4 X-Y-Z axes are joined togetherVoron 2.4 frame with X-Y-Z axes joined togetherParts:16x M3x20 SHCS8x M3x16 SHCSLow Strength Thread LockerTools:2.5mm Hex Key (Allen)Voron 2.4 - XY and YZ joint16 06 2020 Voron 2.4 X-axis. Beam with left and right X-Y JointsI do not have more MGN9H L300 Linear Rails at the moment, so pre-assembled without. Voron 2.4 X-axis. Beam with left and right X-Y Joints (without Linear Rail)Parts:1x Printed Parts1x Aluminum extrusion profile Misumi HFSB5-2020-330 (Voron 2.4 FermioLab frame kit included)8 4x F695 Bearing [Update 17.06.2020. 2x GT2 20T Toothed Idler (5mm ID 6mm W) instead of two dual F695 bearing stacks]8 4x M5 Washer (1mm Thick)8x M5x40 Socket Head Cap Screw (SHCS)2x M5x30 Button Head Cap Screw (BHCS)4x M5x10 BHCS6x M5 Self-Locking Hex Nut6x Spring T-nut M56x ABS Printed Printed Spacer 5.2mm ID x 6.8mm, 0.6mm Thick [Update 17.06.2020 (spacer for GT2 20T Toothed Idlers)]Tools:3, 4mm Allen KeyVoron 2.4 X-axis. Right Side X-Y Joint[Update 17.06.2020. 2x GT2 20T Toothed Idler (5mm ID 6mm W) instead of two dual F695 bearing stacks] Voron 2.4 X-axis. Right Side X-Y Joint14 06 2020 Voron 2.4 - Z axis belt tensioners, Z IdlersSince today my Voron 2.4 has got four belt tensioners, mounted in 4 top corners of the 3D printer frame. Voron 2.4 - Z axis belt tensioner, Z IdlerParts I have used for 4 pcs Voron 2.4 belt tensioners:1x Printed Parts Set4x GT2 20T Toothed Idler (5mm ID 9mm W) included in Powge Voron 2.4 Motion Parts Set4x M3x16 Socket Head Cap Screw (SHCS)4x M5 Self-Locking Hex Nut8x ABS Printed Printed Spacer 5.2mm ID x 6.8mm, 0.8mm Thick 8x Spring T-nut M512x M5x30 Button Head Cap Screw (BHCS)Tools2.5 Hex Key (Allen)Flat Screwdriver Voron 2.4 - Zaxis belt tensioners, Z Idlers13 06 2020 Assembled Gantry, Y-axis - Voron 2.4More photos of the Voron 2.4 Gantry you can find in slideshow box.Voron 2.4 - Gantry, Y-axis assembled Voron 2.4 - Gantry (upside down), Y-axis assembledParts used in this step - Voron 2,4 Gantry (without X-beam): 1x Printed Parts Set2x Aluminum extrusion profile Misumi HFSB5-2020-350 (Voron 2.4 frame kit included)1x Aluminum extrusion profile Misumi HFSB5-2020-240 (Voron 2.4 frame kit included)2x MGN9 Linear Rail l=300mm2x MGN9H Block2x Stepper Motor NEMA17 17HS19-2004S2x GT2 20T Pulley (5mm ID 9mm W)16x F695 Bearing34x Spring T-nut M312x Spring T-nut M58x M5 Hammer Head T-nut30x M3x8 Socket Head Cap Screw (SHCS)2x M3x40 SHCS6x M3x30 SHCS8x M5x16 SHCS8x M5x8 SHCS6x M5x40 SHCS4x M5x30 Button Head Cap Screw (BHCS)2x M3 Washer (0.5mm)20x M5 Washer (1mm)6x M5 Self-Locking Hex Nut2x M3 D5.0 L4.0 Threaded InsertsTools:2.5,3,4mm Hex Keys (Allen)Adjustable Electric Soldering Iron (for M3 Threaded Inserts)Isopropanol (for cleaning the parts)NLGI 1 Grease (for Linear Rail Bearing Blocks)09 06 2020 My Voron 2.4 has already four linear rails mounted on the Z axis.Parts used in this step:4xMGN9H Linear Rail l=300mm60x M3x8 304 Stainless Steel DIN 912 Socket Head Cap Screw60x Spring T-Nut Block for 2020 Aluminium ProfileNeeded Tools: 2x rail_installation_guide_center_x2.stl (3D printed)Digital Calliper2.5mm Hex Key (Allen)Voron 2.4 frame with Z linear rails07 06 2020 I am printing some Voron 2.4 parts right now. https://github.com/VoronDesign/Voron-2/tree/Voron2.4/STLs/VORON2.4Filament: ABS PrimaSelectPrimary Color: Black Accent Color: Red3D Printer: Upgraded Ender 5 without enclosure, Direct Drive ExtruderSlicer: IdeaMaker Ver. 3.4.2.3140Slicing parameters I am using: 6 Bottom and Top solid layers, 6 walls, layer 0.2mm, Extrusion Width 0.4mm, 70% Gyroid Infill.Printing parameters: Temp: 250C/105C, Cooling:0%, Default Printing Speed: 67.5mm/sI have added my slicer profiles for Voron 2.4 printed parts to the "Thing Files". Some Voron 2.4 printed parts25 05 2020 Voron 2.4 - Pre-assembled 3D printer frame. 3D Printer Build Volume X:250mm,Y:250mm Z:250mmVoron 2.4 Frame Dimensions W:410mm D:410 mm H:430 mmUsing 20x20 Aluminum Extrusion - 5 Series, MISUMI HFSB5-2020, Standard Type (FermioLabs Frame Kit)Blind Frame Joints with 16 pcs M5x16mm 304 Stainless Steal Button Head Cap Screw (ISO 7380)I am still waiting for Low Strength Thread Locker delivery. 01 05 2020 VORON 2.4 Motion Parts Kit ordered from Powge17 04 2020 Generated new customized bill of materials for my VORON 2.4 build.* Filament Feed Setup: Direct Feed.* Frame Joint :Blind Joints.* Printer size: 250mm.https://docs.google.com/spreadsheets/d/1erMi0XxXEdxEhJK4wOg0EN6wP1i740O80VATIcL69vk/edit?usp=sharing31 03 2020 250mm³ Voron 2.2 Frame kit from FermioLabs ordered already: Printer build volume: X 250mm, Y 250mm Z 250mmFull set of pre-machined aluminium extrusions; ready to assemble. Including four OpenBuilds angle corner connectors and four M5 T-Slot nuts to mount the bed support extrusions.Voron 2- 250mm3 - Frame Kit. Source:https://fermio.xyz/voron/voron2/frames/5/frame-250mm3Contents•4x HFSB5-2020-430-LCP-RCP•10x HFSB5-2020-370-TPW•2x HFSB5-2020-350•1x HFBS5-2020-330•1x HFSB5-2020-240 (v2.4 forward compatible rear crossbar)•1x HFBS5-2020-200•4x HNTAJ5-5•4x OpenBuilds Angle Corner ConnectorMachiningWrench Hole Machining in Fixed Position•Row Crisscross from Left End Face [LCP]•Row Crisscross from Right End Face [RCP]Tapped Holes on End Faces•Both End Faces [TPW]Version: VORON2 Release: v2.0, v2.1, v2.2 Build: 250x250x250mm Tolerance (Cuts): DIN ISO 2768-1m Color: black (anodized) Material: Aluminium Alloy: EN AC 51400 T5 26 03 2020 Voron 3D Printer stats I have chosen: VORON 2.2 printer size: 300mmBuild volume: X 300mm, Y 300mm Z 300mmPrinter dimensions: W 460mm, D 460mm, H 480mmVoron 2.2 Frame:Blind Joints version.Aluminum Extrusions (Black):Misumi HFSB5-2020-250 1pcMisumi HFSB5-2020-380 1pcsMisumi HFSB5-2020-400 2pcsMisumi HFSB5-2020-420-TPW (ends tapped for M5) 10pcsMisumi HFSB5-2020-480-LCP-RC (access holes drilled on both ends) 4pcsHardware:Angle Corner Connector 4pcsBolts M5x16 20pcsBolts M5x10 4pcsWashers M5 4pcsT-nuts M5 4pcsI can't find the supplier on Aliexpress FermioLabs temporary closed. I'm waiting for an offer from Hobby-Store25 03 2020 Today, I am looking for a supplier that will prefabricate and provide aluminum extrusion profiles for the construction of the frame. 24 03 2020 I have a plan to build my own Voron 2.2 3D printer.Project site: http://vorondesign.com/